LAN settings
This item is displayed on the HOME screen.
Important
-
The administrator password is required to change the settings if it is enabled to change the settings on the operation panel using the administrator password.
To print the network settings, select Print details and select Yes.
Important
-
The network settings printout contains important information about your network. Handle it with care.
Wi-Fi
Wi-Fi setting list
The network settings information of the printer appears when it is connected by Wi-Fi. (Some setting items are not displayed depending on the printer settings.)
| Items | Setting |
|---|---|
| Connection | Enabled (connected)/Enabled (disconnected)/Disable |
| Network name (SSID) | XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX |
| Frequency | 2.4 GHz/5 GHz |
| Wi-Fi security |
Disable WPA-PSK(AES) WPA2-PSK(AES) WPA/WPA2-PSK WPA3-SAE(AES) WPA2/WPA3-PSK WPA-EAP(AES) WPA2-EAP(AES) WPA3-EAP(AES) WPA/WPA2-EAP(AES) WPA2/WPA3-EAP(AES) |
| Signal strength (%) | XXX |
| IPv4 address | XXX. XXX. XXX. XXX |
| IPv4 subnet mask | XXX. XXX. XXX. XXX |
| IPv4 default gateway | XXX. XXX. XXX. XXX |
| IPv6 link-local address | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| IPv6 link-local prefix length | XXX |
| IPv6 manual address | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| IPv6 manual prefix length | XXX |
| IPv6 stateless address 1 | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| IPv6 stateless prefix length 1 | XXX |
| IPv6 stateless address 2 | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| IPv6 stateless prefix length 2 | XXX |
| IPv6 stateless address 3 | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| IPv6 stateless prefix length 3 | XXX |
| IPv6 stateless address 4 | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| IPv6 stateless prefix length 4 | XXX |
| IPv6 default gateway 1 | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| IPv6 default gateway 2 | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| IPv6 default gateway 3 | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| IPv6 default gateway 4 | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| MAC address (Wi-Fi) | XX:XX:XX:XX:XX:XX |
| IPsec settings | Enable (ESP) / Enable (ESP & AH) / Enable (AH) / Disable |
| Printer name | XXXXXXXXXXXXXXX |
| Bonjour service name | XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX |
("XX" represents alphanumeric characters.)
To change the setting, select Settings.
-
Enable/disable Wi-Fi
Enables/disables Wi-Fi.
-
Wi-Fi setup
Selects the setup method for Wi-Fi connection.
-
Easy wireless connect
Select if you specify the settings of the access point information to the printer directly from a device (e.g. smartphone, or tablet) without operating the wireless router. Follow the on-screen instructions of the connecting device for the setup procedure.
-
Manual connect
Select when you perform settings for Wi-Fi manually using the operation panel of the printer.
-
WPS (Push button method)
Select when you perform settings for Wi-Fi using a wireless router supporting a Wi-Fi Protected Setup (WPS) push button method. Follow the on-screen instructions during setup.
-
Other connection types
-
WPS (PIN code method)
Select when you perform settings for Wi-Fi using a wireless router supporting a Wi-Fi Protected Setup (WPS) PIN code method. Follow the on-screen instructions during setup.
-
-
-
Advanced
For details on each setting item:
Wireless Direct
Wireless Direct setting list
The network settings information of the printer appears when it is connected by the wireless direct. (Some setting items are not displayed depending on the printer settings.)
| Items | Setting |
|---|---|
| Connection | Enable/Disable |
| Network (SSID)/device name | DIRECT-XXXXXXXXX XXXXXXXXXXXXXXXX |
| Password | XXXXXXXXXX |
| Frequency | 2.4 GHz/5 GHz |
| Wi-Fi security | WPA2-PSK(AES) |
| No. of printers connected now | XX/XX |
| IPv4 address | XXX. XXX. XXX. XXX |
| IPv4 subnet mask | XXX. XXX. XXX. XXX |
| IPv4 default gateway | XXX. XXX. XXX. XXX |
| IPv6 link-local address | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| IPv6 link-local prefix length | XXX |
| MAC address (Wi-Fi) | XX:XX:XX:XX:XX:XX |
| IPsec settings | Enable (ESP) / Enable (ESP & AH) / Enable (AH) / Disable |
| Printer name | XXXXXXXXXXXXXXX |
| Bonjour service name | XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX |
("XX" represents alphanumeric characters.)
To change the setting, select Settings.
-
Enable/disable Wireless Direct
Enables/disables Wireless Direct.
-
Change SSID/device name
Changes the identifier (SSID/the printer's name displayed on a Wi-Fi Direct compatible device) for Wireless Direct.
-
Change password
Changes the password for Wireless Direct.
-
Connection request confirmation
Changes the display/non-display of the confirmation screen when Wi-Fi Direct compatible devices are connected to the printer.
-
Advanced
For details on each setting item:
-
2.4GHz/5GHz Switch
Sets the frequency to use.
Wired LAN
Wired LAN setting list
The network settings information of the printer appears when it is connected by wired LAN. (Some setting items are not displayed depending on the printer settings.)
| Items | Setting |
|---|---|
| Connection | Enabled (connected)/Enabled (disconnected)/Disable |
| IPv4 address | XXX. XXX. XXX. XXX |
| IPv4 subnet mask | XXX. XXX. XXX. XXX |
| IPv4 default gateway | XXX. XXX. XXX. XXX |
| IPv6 link-local address | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| IPv6 link-local prefix length | XXX |
| IPv6 manual address | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| IPv6 manual prefix length | XXX |
| IPv6 stateless address 1 | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| IPv6 stateless prefix length 1 | XXX |
| IPv6 stateless address 2 | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| IPv6 stateless prefix length 2 | XXX |
| IPv6 stateless address 3 | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| IPv6 stateless prefix length 3 | XXX |
| IPv6 stateless address 4 | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| IPv6 stateless prefix length 4 | XXX |
| IPv6 default gateway 1 | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| IPv6 default gateway 2 | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| IPv6 default gateway 3 | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| IPv6 default gateway 4 | XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX |
| MAC address (Wired LAN) | XX:XX:XX:XX:XX:XX |
| IPsec settings | Enable (ESP) / Enable (ESP & AH) / Enable (AH) / Disable |
| Printer name | XXXXXXXXXXXXXXX |
| Bonjour service name | XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX |
("XX" represents alphanumeric characters.)
To change the setting, select Settings.
-
Enable/disable Wired LAN
Enables/disables wired LAN.
-
Advanced
For details on each setting item:
Advanced setup
-
Set printer name
Specifies the printer name.
Note-
You cannot use the same printer name as that already used for other LAN connected devices.
-
You cannot use a hyphen for the initial or last character of the printer name.
-
-
TCP/IP settings
Performs IPv4 or IPv6 setting.
-
WSD settings
Setting items when you use WSD (one of the network protocols supported in Windows).
-
Enable/disable WSD
Selects whether WSD is enabled or disabled.
Note-
When this setting is enabled, the printer icon is displayed on the Network Explorer in Windows.
-
-
Optimize inbound WSD
Selecting Enable allows you to receive the WSD printing data faster.
-
Timeout settings
Specifies the timeout length.
-
-
Bonjour settings
Setting items when you use Bonjour.
-
Enable/disable Bonjour
Selecting Enable allows you to use Bonjour to perform the network settings.
-
Service name
Specifies the Bonjour service name.
Note-
You cannot use the same service name as that already used for other LAN connected devices.
-
-
-
IEEE802.1X settings
Sets the IEEE802.1X authentication method, etc.
-
LPR protocol settings
Enables/disables the LPR setting.
-
RAW protocol
Enables/disables RAW printing.
-
LLMNR
Specifies ON/OFF of LLMNR (Link-Local Multicast Name Resolution). Selecting ON allows the printer to detect printer's IP address from the printer name without a DNS server.
-
IPP settings
Selecting Enable allows you to print via the network with the IPP protocol.
-
Wi-Fi DRX settings
Selecting Enable allows you to activate discontinuous reception when using Wi-Fi (discontinuous reception).
Note-
Depending on the Wi-Fi router used, discontinuous reception may not be activated even though Enable is selected.
-
Discontinuous reception is enabled only while the printer is on standby. (The LCD is in the screen saver mode.)
-
-
Wired LAN DRX settings
Selecting Enable allows you to activate discontinuous reception when the printer is connected to a device compatible with wired LAN.
-
IPsec settings
Selecting Enable allows you to specify the IPsec security.
